New Bullet Mould

[Creeker]

Contacted Swede Nelson & asked for a 2 cavity NOE 454-255-RF mould. He had one & only a few days later it arrived. The man is quick.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02596.jpg

Open her up & took a look. The blocks were clean, no burrs or out of place tool marks. The cavities were beautiful. Removing the sprue plate, screw & set screw I gave the blocks a going over with a nylon brush & hot soapy water. She looked good. The sprue plate was cleaned with starting fluid & brush.

Before cleaning
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02597.jpg

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02598.jpg

After
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02599.jpg

I coated the top of the blocks & both sides the sprue plate with Frankford Arsenal Drop Out, installed the plate, adjusted & replaced the set screw.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02600.jpg

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02602.jpg

[Creeker]

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02603.jpg

Installed the blocks on RCBS handles & placed on the stove to warm up along with a Lyman 4 cavity 358429.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02605.jpg

Once the melt was at 750 degrees & the blocks up to temperature the casting began. The mould dropped acceptable bullets after only a few dumps. The bullets fell with little effort. These are the first.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02607.jpg

I sized at .454 for my 1973 New Model Blackhawk Ruger using LBT Blue lube. These fit my cylinder perfectly. The bases fill out well with a loose sprue plate, the lube groove is plenty large, & the meplat should be a killer.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02619.jpg

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02621.jpg

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02620.jpg

I’ll load these first chance & see how they do, I’m expecting good things. BTW they came from the mould using wheel weight alloy at .454+ & 258 grains.

[Creeker]

Finally took a break from firewood & fishing to try this bullet. I loaded 50 with 7.0 grains of HP38 & a Tula primer.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Loading%20Equipment/Dillon%20Square%20Deal%20B/DSC02658-1.jpg

The bullet has a nice crimp groove. These were lubed with LBT Blue. The first target fired was on a previously used paper plate. If you throw out the called flyer its 1 ½”. All targets were shot at 30 yards.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02726.jpg

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02723.jpg

[Creeker]

Second target was 1 7/8” & third 2 1/4”
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02725.jpg

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02724.jpg

Notice the vertical stringing no doubt do to the fuzzier than normal front sight today. It’s hard to repeat the vertical hold & I would have been better served holding center.

These bullets were cast from air cooled wheel weight alloy. The barrel shows no signs of leading though I haven’t cleaned to be perfectly sure. I do believe however the load was too lite & needs to be increased. The cases were sooty so next load will be at least 7.5 grains. I’ll need the extra velocity as my rear sight is bottomed.
http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02731.jpg

http://i66.photobucket.com/albums/h244/Creekerpics/Loading%20Room%20101/Bullets/454-255-RF/DSC02733.jpg

[colbyslanbia]

My better shooting Krags have bores that slug at .309-.310", minimum, at the muzzle. I am considering buying a Lee mould that casts 185 gr. round nosed .312" projectiles